English > Support
Help wanted at Script -postersfolderjpg_en-
Ivek23:
Thank you, I am glad to be edited problem.
Jabberwocky:
Hallo,
I write again maybe it was overlooked,
A question about the script "posterswithsamename_en" the setting is so one jpg file is made with the same movie name. Could it so change:
MovieName_Poster.jpg or
MovieName_Thumbnail.jpg
the original script I give this time as an annex to
Thanks for your work
regards Jabberwocky
Ivek23:
--- Quote from: Jabberwocky on September 21, 2016, 03:52:24 pm ---Hallo,
I write again maybe it was overlooked,
A question about the script "posterswithsamename_en" the setting is so one jpg file is made with the same movie name. Could it so change:
MovieName_Poster.jpg or
MovieName_Thumbnail.jpg
the original script I give this time as an annex to
Thanks for your work
regards Jabberwocky
--- End quote ---
Unfortunately, I have not found any solution for the script, to make the script work for the introduction of the transfer of posters in PVD.
In turn, the last PVD 1.0.2.7 version of a feature that when you press a button to " re-read file information " for a particular movie you by the poster box added any posters or pictures that you have in the movie folder (poster, thumbnail, front cover, disc(CD) and other images). Transfer all the images in the movie folder, even then, when in this folder also added there any other image folder. This is from my own adequately experienced when I was looking for solutions to the script and I was in the movie folder contains an additional folder. Further folder with images to disc and front cover has been ever since the last time I was looking for solutions to your previous application. These pictures were added to the poster box but only when the same filename as moviename. Vmovie folder may also be with such a name " 10_Things_I_Hate_About_You_R1_Custom- [cdcovers_cc] -cd1 " and will then be in the poster field.
To test and you will see the coco and then what to do.
pelisdb:
If I have understood what you wanted, I think this should work. It's not a Poster script but a movie script that only loads the poster and cover images, as I haven't found a way to load more than one image with the poster scripts.
Jabberwocky:
Hello,
as I wrote above, the two script run optimally. I explain myself badly.
My film folder looks like this: AnyMovie.mp4
AnyMovie_Poster.jpg (Big Picture)
AnyMovie_Thumbnail.jpg (screenshots)
AnyMovie_Snap1.jpg (A snapshot snap1, Snap2 ...)
AnyMovie_Front.jpg (Not Always)
AnyMovie_Back.jpg (Not Always)
AnyMovie_Cover.jpg (Not Always)
With the script "posterswithsamename_en" I can only upload the poster if his name: AnyMovie.jpg
But my pictures are made, the moviename and an appendix: _Poster
_Thumbnail
_Snap1
therefore I need a change in the script, I understand the function in the script that the path is copied from the movie, then the file extension from AnyMovie.mp4 in AnyMovie.jpg is change,
and if this file exists is played section in the poster.
The position (poster or screenshot), I could change the script.
What I need is the function in the script not only the file extension is changed but also the Notes (as _Poster.jpg) to the path is copied added, and since I do not get ahead.
Point me to the end as follows:
1. Copy file path
2. Remove the leaves file extension
3. merge path+ _Poster
4. Insert file extension .jpg
5. Seeking file
6. if found
7. then save in Section Posters
@Ivek: The "re-read file information" option I know, but I do not want that all images you see in the Poster Section.
@pelisdb: No. I do not want a script multiple images loading, I want to with Relevant script the right image in the right section.
e.g. Script_Poster Selects file AnyMovie_Poster.jpg and Stores in Section posters.
Hope the explanation is better. Working with a translator my English is not the best.
regards Jabberwocky
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version